How to Fix a Dead Kia Picanto Key Fob
The Kia Picanto is a city car that can zip through traffic gaps and width limits as if they weren't there. It's a small car with lots of features.
There are a number of reasons for why your kia picanto key fob may not be working. A dead battery is the most frequent reason.
Dead Coin Battery
A battery that is dead is the most frequent cause of a Kia Picanto's key fob not working. Usually the key fob will display warning signs before it dies, such as losing range or having erratic behavior. If you notice any of these warning indications, it is recommended to replace the battery before it completely fails. Choose a replacement battery that has the same voltage, size and specification as the original.
If the key fob isn't working, it may be time to visit a dealer to purchase a replacement. Only then can you know that the new key fob will be compatible with your vehicle and will be programmed correctly. If you attempt to reprogram an ignition key fob without following the proper procedure could harm the chip's internal circuit and cause it to stop working.
A receiver module that has acquired a fault is another possibility. This could be due to an unintentional chip damage or wear and tear over time. The signs of this issue can be difficult to detect but it's important to look into the issue whenever you can. If your key fob is not working, or the spare doesn't work and you are unable to use it, contact an auto dealer for assistance. They can help you identify the problem and fix it.
Faulty Chip
The key fob contains a chip inside it that sends an electronic signal to the computer in the car. If the chip becomes corrupted and the code is not transmitted correctly, the key fob will be properly transmitted and the immobilizer will activate. This can happen due various reasons. One of the causes is a battery that is not fully charged in the key fob. Another issue is water damage. If the fob becomes wet, it's likely that it will cease to function.
A damaged chip may be the cause of a Picanto key fob not turning on the engine. If you have replaced the battery and tried reprogramming the fob but it doesn't work, it could be because the circuit board is damaged. It is necessary to replace the circuit board in this case.
Press the button on the back to release the fob. Once you have done this, you are able to take off the mechanical key. The video below will guide you how to replace the battery inside the key fob. Choose a battery with the same voltage and dimensions. The Fob might be damaged if you choose the wrong type of battery. After replacing the battery you must check it by pressing the lock button. If it works, then you have a great Fob.
Faulty Receiver Module
Your key fob is not durable and can take a lot of abuse. Over time, its battery contacts and buttons can become damaged and stop working properly. It's simple to repair it by using a few simple tools.
To function, the fob must send a signal to a receiver in your car. If the module is not functioning properly, your fob will not be able to open or start your vehicle. There are several different possible causes of this problem but the first step to try is resetting the fob.
This is accomplished by disconnecting the cable and then letting the battery with 12 volts drain completely. Then, connect the negative and positive cables in reverse order.
If the battery is in good working order and the fob doesn't have any water damage, the issue could be due to the signal. This could be due several factors, such as interference from nearby transmitters as well as objects that operate on the same frequency band as Picanto's Receiver.
Key fobs have rubber seals which prevent the electronic chip from becoming wet. However when they are submerged in water, the chip could be damaged. It is essential to keep your key fob free of the water and only use key fobs that have waterproof designs.
Programming replacement key fob kia is a convenient way to unlock and start your vehicle. You can also utilize the key fob to control your vehicle. It is essential to understand how to use your key fob, particularly if you are traveling in harsh conditions or have a limited mobility. Fortunately, there are plenty of Kia Picanto key fob tricks to help you out with this!
If your key fob stopped working out of the blue, it could have a problem with its internal chip. It is rare but it could happen. To identify the issue, it is best to talk to an Kia dealer.
If you want to, you can attempt to reset your Picanto key fob. The procedure is quite simple and can be carried out at home. The first step is to take the key fob from the ignition switch. Then, connect the diagnostic tool to the OBDII port on the dash, and turn on the engine. The diagnostic tool will seek out details about your Picanto. This includes the VIN number, make and model.
You can also check for dead batteries. The clips made of metal in the key fob hold the battery and complete the circuit. If the retaining clips are loose, it can disrupt the flow of electricity causing a loss in functionality.